Search Results

This paper presents a study of mixture formation in the combustion chamber of a direct-injection SI engine. In-cylinder flow measurement was conducted using laser Doppler velocimetry (LDV) and particle image velocimetry (PIV), and visualization of fuel vapor behavior was done using laser-induced fluorescence (LIF). Further, fast response flame ionization detector (FID) was used to measure the hydrocarbon (HC) concentrations in the vicinity of the spark plug. Thereby mixture concentrations in the vicinity of the spark plug, within the mixture distribution observed using LIF, were quantified. Results revealed that an upward flow forms near the center of the cylinder in the latter half of the compression stroke and goes from the piston crown toward the cylinder head. This upward flow is caused by the synergistic effect of the swirl motion generated in the cylinder and the cylindrical bowl provided in the piston crown eccentrically to the central axis of the cylinder.

This paper describes the magnetic circuit design of a coaxial AC motor system, comprising one stator and two rotors, and the test results obtained for a prototype motor. The rotors of the motor share the same stator core and coils, and each rotor uses its magnetic part as a yoke. Magnetic flux linkage of each rotor was determined in consideration of the maximum torque/power conditions and maximum motor speed. Finite Element Method were utilized to design a magnetic circuit for achieving the magnetic flux linkage specification. Tests conducted with a prototype motor showed that the torque characteristics can be divided into magnetic torque and reluctance torque, just like an ordinary IPM motor. Each torque level was improved through field-weakening control. The combined torque obtained when the two rotors were driven simultaneously approximately equaled the sum of the individual torques when the rotors were driven independently.

Experimental investigations were previously conducted with a direct-injection diesel engine with the aim of reducing exhaust emissions, especially nitrogen oxides (NOx) and particulate matter (PM). As a result of that work, a combustion concept, called Modulated Kinetics (MK) combustion, was developed that reduces NOx and smoke simultaneously through low-temperature combustion and premixed combustion to achieve a cleaner diesel engine. In subsequent work, it was found that applying a low compression ratio was effective in expanding the MK combustion region on the high-load side. The MK concept was then combined with an exhaust after-treatment system and applied to a test vehicle. The results indicated the attainment of ULEV emission levels, albeit in laboratory evaluations. In the present work, the combination of the MK combustion concept and certain fuel properties has been experimentally investigated with the aim of reducing exhaust emissions further.

A multiple-link variable compression ratio (VCR) mechanism is suitable for a long-stroke engine by providing the following characteristics: (1) a nearly symmetric piston stroke and (2) an upper link that stays vertical around the time of the maximum combustion pressure. These two characteristics work to reduce force inputs to the piston. The maximum inertial force around top dead center is reduced by the effect of the first characteristic. The second characteristic is effective in reducing piston side thrust force and helps ease piston pin lubrication. Because of the combined effect of these characteristics, the piston skirt can be made smaller and the piston pin can be shortened. That makes it possible for the piston skirt and piston pin to move between the counterweights, resulting in a downward extension of the piston stroke. As a result, a longer-stroke engine mechanism can be achieved without making the cylinder block taller.

Simultaneous crank-angle-resolved measurements of gasoline vapor concentration, gas temperature, and liquid fuel droplet scattering were made with three-color infrared absorption in a direct-injection spark-ignition engine with premium gasoline. The infrared light was coupled into and out of the cylinder using fiber optics incorporated into a modified spark plug, allowing measurement at a location adjacent to the spark plug electrode. Two mid-infrared (mid-IR) laser wavelengths were simultaneously produced by difference-frequency-generation in periodically poled lithium niobate (PPLN) using one signal and two pump lasers operating in the near-infrared (near-IR). A portion of the near-IR signal laser residual provided a simultaneous third, non-resonant, wavelength for liquid droplet detection. This non-resonant signal was used to subtract the influence of droplet scattering from the resonant mid-IR signals to obtain vapor absorption signals in the presence of droplet extinction.

Engines in Japan have higher output versus small displacement (bhp/liter) and require low phosphorus content in the engine oils to meet the most stringent exhaust emission regulation in the world. The market survey of typical API SF oils in Japan showed that the average phosphorus content was approximately 0.07 %. Under such circumstances engine oils provide good performance with the usage of secondary zinc di-alkyldithiophosphates (Zn DTP) for valve train wear protection, addition of friction modifiers for fuel economy, etc.

Turbulent flows in a model engine having a square piston were analyzed in detail by using a numerical simulation method with higher-order accuracy to perform simulations on an orthogonal homogeneous grid without grid motions. Calculations were performed during several continuous engine cycles. A better understanding of the cycle-by-cycle differences, i.e., cyclic variations, in flow fields may lead to more effective ways of stabilizing combustion.

In order to improve the accuracy of the coil temperature prediction, detailed fundamental experiments have been conducted on thermal resistances that are caused by the void air gap and contact surfaces. The thermal resistance of the coil around the air gap can be calculated by an air gap distance and air heat conductivity. Contact surface thermal resistance between the core and the housing was constant regardless of the press-fitting state in this experiment. Prediction accuracy of the coil temperature is improved by including the heat resistance characteristics that is obtained by the basic experiment to conjugate heat transfer analysis model.

Various heat resistant alloys are being introduced for use in automobile emission equipment, such as thermal reactors and catalytic converters. For the past several years Japan has been developing alloys which emphasize oxidation resistance. Therefore, oxidation phenomena have been thoroughly researched and clarified. On the other hand, embrittlement, which is a marked deterioration similar to oxide deterioration, has not been studied sufficiently. The major subjects of investigation were the two forms of embrittlement in austenitic heat resistant alloys, caused by the precipitation of σ phase and the absorption of Nitrogen. Useful information was obtained from these results.

Nissan Motor has put on the European SUV market a 2.2-L direct-injection diesel engine with a diesel particulate filter (DPF) system that complies with the EURO IV emission regulations. This paper describes the DPF system, cooperative control of a variable geometry turbo (VGT) and exhaust gas recirculation (EGR), and a high-accuracy lambda control adopted for this engine. In order to achieve a compact DPF, the high-accuracy lambda control was developed to reduce variation in engine-out particulate matter (PM) emissions. Moreover, the accuracy of the technique for predicting the quantity of PM accumulation was improved for reliable detection of the DPF regeneration. Prediction error for PM accumulation increases during transient operation. Control logic was adopted to correct the PM prediction according to lambda fluctuation detected by an observer for lambda at cylinder under transient operating conditions. The observer is corrected lambda sensor output.

Basic vehicle performance, such as Safety, Comfort and Economy, are by dependent on tire performance, and it is the air pressure in the tire which assures this performance. However, tire air has a tendency to leak naturally, making it necessary to check them periodically. Since a deterioration in vehicle performance resulting from a drop on tire air pressure can not be directly felt by the driver, the number of people maintaining their tires sufficiently is relatively few. There have been many tire pressure warning devices developed which advise the driver when the pressure drops below a prescribed level. Differing from conventional devices, the TWD-III features a 7-step digital display (at a pitch of 0.1 kgf/cm2) which shows the pressure of each tire within an optional range, and it also has a flat tire warning function. The employment of echo effect from clystal vibrator resonance precludes the need to attach a power source on the tire.

Door guard beams have been developed through the utilization of ultra high strength steel (tensile strength>100 kg/mm2). At first, the sheet metal gauge was reduced in proportion to the strength of the ultra high strength without changing the shape of the beam section. This caused beam buckling and did not meet guard beam specifications. Analyzing this phenomena in accordance with the buckling theory of thin plates, a design criteria that makes effective use of the advantages of ultra high strength was developed. As a result, our newly designed small vehicle door guard beams are 20% lighter and 26% thinner than conventional ones. This makes it possible to reduce door thickness while increasing interior volume.

The SR engine is a new medium-size, all aluminum (cylinder block, head, rocker cover and oil pan) in-line 4-cylinder gasoline powerplant developed as a replacement for CA engine in Nissan's compact passenger cars. The development aim set for this engine was to achieve excellent power output and ample torque in the middle-and high-speed ranges, as well as a clear, linear engine sound up to the red zone. These performance targets have been achieved through the use of the 4-valve-per-cylinder DOHC design featuring a Y-shaped valve rocker arm system. This system allows a straight intake port for high power output and a narrow valve angle for a compact combustion chamber. The result is ample torque output as well as good fuel economy.

A suitable GF-5 engine oil formulation is investigated to improve the fuel economy of gasoline engines with hydrogen-free DLC-coated valve lifters. Molybdenum dithocarbamate (MoDTC) is shown to be a suitable friction modifier for low viscosity grade engine oils like 0W-20. A suitable Ca salicylate detergent is also determined from several types examined for maximizing the friction reduction effects of MoDTC. The most suitable Ca salicylate has a chemical structure capable of forming a borophosphate glass film on metal surfaces, which is known to improve the effects of MoDTC. A high viscosity index Group III base oil (VI>140) is also effective in improving fuel efficiency. It is further clarified that the structural design of the polymethacrylate viscosity modifier is another important factor in reducing engine friction.

Improving the impact strength of the differential gears is one way to reduce the size and weight of the final drive unit. Previously, we developed high-strength steel for gear use by adding molybdenum and reducing impurities such as phosphorus and sulfur. However, additional improvement of impact strength is required these days due to higher engine torque and demands for further weight reductions. Toward that end, we focused on boron, which has been used as an element for improving hardenability, and analyzed what effect its addition would have on impact strength. Useful knowledge was obtained for improving impact strength through enhancement of grain boundary toughness. Various steels were then produced experimentally and used in gear strength tests. The results made it possible to improve impact strength while reducing the content of other alloys, resulting in the development of a chromium-molybdenum-boron case hardening steel with superior cold forgeabilty.

This paper describes the motor and inverter system developed for the Nissan LEAF that has been specifically designed as a mass-produced electric vehicle. The system produces maximum torque of 280 Nm and maximum power of 80 kW. The motor achieves a small size, high power, and high efficiency as a result of adopting the following in-house technologies. The magnetic circuit design was optimized for an interior magnet synchronous motor to attain the maximum performance figures noted here. The material technologies of the rotor and the stator facilitate high efficiency and the production technology achieves high density winding. The cooling mechanism is optimally designed for a mass-produced electric vehicle. The inverter incorporates the following original technologies and application-specific parts to obtain cost reductions combined with reliability improvements. The power module has an original structure with the power devices mounted directly on the busbars.

High strength transmission gears have been developed for use in the final gear set of front-wheel-drive vehicles. The steel used as the gear material has a higher molybdenum content, allowing more austenite to be retained following carburizing than is possible with chromium steel. As a result, the steel can be subjected to higher intensity shot peening by using harder peening particles which are projected by an air-nozzle peening system. With this procedure, the fatigue strength of the gears can be increased 1.6 times over that of conventional gears.

A compact, high-performance and durable metal-supported catalyst has been developed by using the properties of the metal support effectively. The advantages of the metal-surpported catalyst against the ceramic-supported one are higher geometrical surface area, higher heat conductivity and thinner wall thickness. Higher geometlical surface area and higher heat conductivity lead to higher conversion efficiency after durability test and it allows reduction in catalyst volume. And the thinner wall thickness lowers gas flow resistance. But also, the metal-supported catalyst has the disadvantage of larger heat expansion and it requires special structure and material.

Engine oil with viscosity lower than 0W-16 has been needed for improving fuel efficiency in the Japanese market. However, lower viscosity oil generally has negative aspects with regard to oil consumption and anti-wear performance. The technical challenges are to reduce viscosity while keeping anti-wear performance and volatility level the same as 0W-20 oil. They have been solved in developing a new engine oil by focusing on the molybdenum dithiocarbamate friction modifier and base oil properties. This paper describes the new oil that supports good fuel efficiency while reliably maintaining other necessary performance attributes.

Surface roughness of steel sheet for automotive use is one of the most important control items, because the surface roughness influences image clarity of painted surface, press formability and easiness in handling during manufacturing and processing of steel sheets. Laser texturing technology is introduced into a roll finishing process of cold rolling, and new type of regular surface roughness profile can be processed on the surface of steel sheets. Effective application method of this technology is investigated at the present day. In Japan, Laser-textured dull steel sheets are used for outer-panels of automotive body as the first application. And image clarity after painting of outer panels has been successful in improving. Nowadays, Laser texturing technology is actually used for manufacturing the high image clarity steel sheets, and they are manufactured in large quantities. Another application of Laser texturing technology is for the inner parts which require pressformability.